Studer-innotec RCC-03 Instrukcja Użytkownika

Studer Innotec Rue des Casernes 57 CH - 1950 Sion Tel: +41 (0)27 205 60 80 Fax: +41 (0)27 205 60 88 E-mail: [email protected] Web: www.studer-in

Studer Innotec 10 Updating must be done in the full awareness of the cause and is always the responsibility of the customer. Partial updates may cause

RCC 11 INTRODUCTION Congratulations! The purchase of an RCC remote control offers you unlimited access to the various functions of the devices in

Studer Innotec 12 CONNECTION The RCC-02 remote control must be firmly fastened using 3 screws on a flat support. The remote control RCC-03 is meant to

RCC 13 DIMENSIONS RCC-02 RCC-03

Studer Innotec 14 QUICK START GUIDE The remote control RCC gives you access to a many settings possibilities. However, in most cases the setting of tw

RCC 15 You can now adapt your installation to the source which it is connected to. Max. current of the AC source (power-sharing) {1107}. In ca

Studer Innotec 16 ACTIVATION OF THE FUNCTION SMART-BOOST If your AC-In source is limited in power, the Xtender can work as a support and add the missi

RCC 17 BASIC DISPLAYS When the remote control is connected to an Xtender, it is possible to access different display menus divided into distinct

Studer Innotec 18 ACTIVATING AND DEACTIVATING THE COMBI XTENDER When one of the displays is visible, it is possible to activate or deactivate the Xten

RCC 19 ADJUSTMENT OF THE RCC REMOTE CONTROL This screen gives you access to the remote control basic settings. From one of the basic menu items,

Studer Innotec 2 Reference This document applies to versions of firmware V1.2.0 or higher of the remote control. Copyright Copyright © Studer Innotec

Studer Innotec 20 Duration of the back-lighting {5009} This configuration allows you to determine after how much time of inactivity the back-lighting

RCC 21 programs. The file is written in a directory called STATS and in a subdirectory which indicates the date of backup. Backup of remote contr

Studer Innotec 22 INFORMATION ON THE OPERATING MODE OF THE INSTALLATION There are two different views for displaying information on the system : A si

RCC 23 The following information is available: With regard to the grid input • AC In input voltage • AC In input current • AC In input power • In

Studer Innotec 24 EVENT HISTORY This screen allows you to view the various events that have occurred in the installation. The events that occur in y

RCC 25 ERROR INCORRECT INPUT FREQUENCY The voltage at AC IN does not have a frequency included in the admissible range for the Xtender. Solution:

Studer Innotec 26 The voltage ripple on the batteries may be caused by their ageing. In this case, lower the charge current. MESSAGE POWER SHARING EX

RCC 27 ADJUSTMENT OF THE COMBI XTENDER GENERAL The Xtender inverter/charger has been designed to ensure that all basic functions of an energy man

Studer Innotec 28 According to the user level selected, it is possible to access several hundred configurations. For this reason, each configuration h

RCC 29 Note, that if the smart boost function is activated, it is possible to discharge the battery even if the inverter function is locked. Aut

RCC 3 Table of contents Foreword...

Studer Innotec 30 Number of critical battery under-voltages before final stop {1305} and Leadtime to counting the critical battery under-voltages allo

RCC 31 The bulk charge and floating phases cannot be deactivated. If the conditions for starting a new battery charge cycle have come together,

Studer Innotec 32

RCC 33 Charge current {1138} Use this value in order to adapt the charge current to the battery. With this configuration, the maximum current to

Studer Innotec 34 Absorption phase {1451} During this phase, the battery accumulates the final percentages of the energy it is storing. This phase is

RCC 35 Equalization before absorption phase {1291} This configuration determines in the charge cycle, in which equalization will be activated, if

Studer Innotec 36 End of equalization activated by the current {1168} The equalization phase can be interrupted if the charge current of the battery g

RCC 37 Level of battery under-voltage at no load {1108} Allows adjustment of the battery’s low voltage level at which the inverter and smart boos

Studer Innotec 38 Delay before passing to inverter {1198} When the input voltage is below the transfer voltage to the inverter, the transfer relay doe

RCC 39 The auxiliary contacts respond to various signal types presented graphically below. The following types of basic events may activate the c

Studer Innotec 4 Stop Inverter overvoltage ...

Studer Innotec 40 Limit the time of activation {1512} {1513} Maximum duration of activation {1514} {1515} When the conditions are met, either one or t

RCC 41 Inverter or smart boost overload {1228} {1336} Activates the contact in the event of an error due to excessive power in the inverter or th

Studer Innotec 42 The auxiliary contact will only be activated after the battery exceeds again a certain voltage value and also after a duration, both

RCC 43 o Time of end of activation {1273} {1382} • Program 2 {1274} {1383} o Days of the week {1275} {1384} o Time of start of activation {1276}

Studer Innotec 44 INFORMATION ON THE SYSTEM The system information allows you to check the versions of the various elements of your installation. REMO

RCC 45 UPDATES The RCC remote control program as well as the code in the inverters/chargers of the Xtender series can be updated in order to inte

Studer Innotec 46 APPLICATION EXAMPLES The examples below illustrate some implementation options for current installations. Useful configurations for

RCC 47 USE TO INCREASE THE POWER ON AN EXISTING INSTALLATION Description: The availability of an inverter or a inverter/charger allows its power

Studer Innotec 48 ANNEXES ANNEXE 1 : LIST OF CONFIGURATION INTERDEPENDENCIES N° Configuration N° Minimum limit by N° Maximum limit by 1108 Undervo

RCC 49 1308 Temperature at which the charge current begins to reduce 1115 Maximum operating temperature 1140 Battery maintenance voltage (floa

RCC 5 Output voltage {1286}...

Studer Innotec 50 NOTES

RCC

Studer Innotec 6 général use : Inverter, Charger with grid...

RCC 7 FOREWORD This manual contains information relating to the functioning of the RCC-02 and RCC-03 remote controls. The use of certain functio

Studer Innotec 8 STUDER INNOTEC CONTACT DETAILS Studer Innotec Rue des Casernes 57 CH – 1950 Sion Tel. +41 (0)27 205 60 80 Fax. +41 (0)27 205 60 88

RCC 9 WARNINGS AND CAUTION WARRANTY Studer Innotec issues on this product, which they have manufactured and offered for sale, a two year warranty